Hydraulic Oil
Transmits power in hydraulic systems while protecting pumps, valves, and cylinders from wear, rust, and foaming.
- Injection Molding
- Presses
- Excavators
Hydraulic oils, gear oils, compressor oils, turbine oils, and greases engineered to cut downtime, extend equipment life, and protect your production line.
Lubricant Categories
Industrial Clients
Technical Support
Delivery Lead Time
Each lubricant is formulated for a specific load, speed, and temperature. Pick a category to see typical grades, standards, and where it is used.
Transmits power in hydraulic systems while protecting pumps, valves, and cylinders from wear, rust, and foaming.
Extreme-pressure protection for enclosed gearboxes under heavy shock loads and high torque.
High oxidation stability and low carbon formation for rotary screw and reciprocating air compressors.
Long-life oil with excellent water separation and rust protection for steam and gas turbine circuits.
Lithium, lithium complex, and polyurea greases for bearings, bushings, and slow-moving components.
Heat-resistant complex greases for kilns, ovens, and bearings that operate at sustained high temperature.
Cutting oils and water-miscible coolants that reduce friction and heat at the tool and workpiece interface.
Thermally stable fluid for closed-loop heating systems, resisting cracking and sludge at high bulk temperature.
Lubricants suitable for incidental food contact in production environments where hygiene is critical.
Select your industry to see typical equipment and the lubricants most often specified.
Continuous production lines depend on clean hydraulics, reliable gearboxes, and stable compressed air. Lubricant failure here stops the whole line.
Keep hydraulic oil cleanliness under control. Most hydraulic failures start with particle contamination.
Quick guides to read lubricant datasheets and match the grade to your machine.
Kinematic viscosity at 40°C (mid-point, cSt)
| Grade | cSt | Typical Use |
|---|---|---|
| VG 32 | 32 | Hydraulics in cool environments, light spindles |
| VG 46 | 46 | General hydraulics, turbines, compressors |
| VG 68 | 68 | Hydraulics in warm climates, compressors |
| VG 100 | 100 | Light-duty gearboxes, slides |
| VG 150 | 150 | Medium-load enclosed gears |
| VG 220 | 220 | Most common industrial gear oil |
| VG 320 | 320 | Heavily loaded gearboxes |
| VG 460 | 460 | Heavy shock loads, slow speeds |
Consistency classes from semi-fluid to firm
| NLGI | Feel | Typical Use |
|---|---|---|
| 000 / 00 | Semi-fluid | Centralized systems, gearboxes |
| 0 | Very soft | Centralized lubrication, cold climates |
| 1 | Soft | Low-temperature, pumpable systems |
| 2 | Medium | General-purpose bearings (most common) |
| 3 | Firm | High-speed bearings, vertical shafts |
Always confirm the grade against the equipment manufacturer's recommendation. These tables are general guidance only.
Four questions narrow down most lubricant decisions before you ever open a catalogue.
Start with the equipment manufacturer's recommended viscosity grade and specification.
Operating and ambient temperature decide the viscosity grade and base oil type needed.
Heavy loads need higher viscosity and EP additives. High speeds usually need lower viscosity.
Moisture, dust, chemicals, or food contact may call for special formulations or approvals.
Good lubricant choice only pays off when it is stored, applied, and monitored correctly.
Regular sampling tracks viscosity, acidity, water, particles, and wear metals before failures occur.
Use breathers, filtration, and clean transfer equipment to keep particles and water out.
Store drums sealed, indoors where possible, and use first-in first-out stock rotation.
Dedicated, labeled containers and fill points prevent cross-contamination and wrong-oil errors.
Specifications commonly referenced when selecting industrial lubricants.
It is best to avoid it. Different additive packages and base oils can be incompatible and reduce performance. If a change is needed, follow a proper flush and changeover procedure.
There is no single interval. It depends on the equipment, operating conditions, and oil type. Condition-based changes guided by oil analysis are usually more cost-effective than fixed schedules.
Mineral oils are refined from crude oil and suit most standard conditions. Synthetic oils offer better stability at extreme temperatures and often longer drain intervals, at a higher purchase price.
NLGI 2 is the most common for general bearings. Softer grades suit centralized systems and low temperatures, while firmer grades suit high-speed or vertical applications. Confirm with the OEM.
Yes. We supply packaged products, drums, IBC totes, and scheduled delivery for regular accounts. Contact us with your volume and location for details.
Send us your equipment list and operating conditions. Our team will recommend the right lubricants and supply schedule.